Norwegische Vorschrift, 2012/2017 (Englisch)

From Wiki-WindPRO
Revision as of 18:07, 21 June 2024 by Robin (talk | contribs)
(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
Jump to navigation Jump to search

Zur deutschen Hauptseite | Alle deutschsprachigen Seiten

The Norwegian guideline was in 2012 replaced by “Veileder til retningslinje for behandling av støy i arealplanlegging (T-1442/2012)”, later replaced by a 2021 version, which is described in document M-128 – 2020 from Miljødirektoratet.The revision does not change the the standard method used in WindPRO, but primarily provides a guideline for use of Nord2000.

The 2012 guideline is a combination of the Swedish guideline “Ljud från Vindkraftverk” from 2001 and the previous Norwegian guideline. It is also incompatible with the old guideline, which cannot simply be recalculated with the revised guideline.


Calculation setup

The calculation model is selected by choosing "Norwegian 2012" as Noise calculation model.


Wind speed

The Norwegian guideline describes a complex method of adjusting 10 m/s with actual roughness along the line of the older Swedish guideline, however advise as a more practical solution that calculations are done at the highest source noise level regardless of wind speed. As the typical wind profiles in Norway are governed not by roughness, but by topography only the highest source noise level option is available in windPRO.

In practice windPRO will consider the noise curve in the noise record selected for the turbine and pick the wind speed with the highest source noise level.


Frequency

Calculations within 1000 m of any turbine in the calculation can actually be calculated without octave data. However for wind farms larger than one turbine the 1000 limitation will almost certainly be exceeded and so octave band distributions are required. If the turbine noise record used does not hold octave data a generic distribution is fitted to the dBA value of the highest noise value.


Wind direction

Whereas the previous guideline advised an upwind reduction, the present guideline refuses this option. The meteorological coefficient should remain 0.


Offshore wind farm

In case of offshore wind farms this option is hatched. The methodology is the same as for the Swedish model and the calculation method is almost identical.


Time domain

The Norwegian codes operate with noise values as Lden, where den is an abbreviation of day-evening-night. It represents a weighted average of noise, where noise during evening and night is penalized. The parameters can be seen or modified by pressing the Edit period button as seen below.

The period definition of day, evening and night can be set here, as well as the penalty due for each period.

Because of the Lden calculation method different noise modes can be set for the turbines for day, evening and night and WindPRO will calculated the combined Lden. If all periods use the same noise mode Lden corresponds to Leq24 + 6,4dB.


Noise limits

Noise limits in Norway are governed by zoning. Dwellings receiving more than Lden = 40 dB(A) must be calculated. The noise limit of the dwelling depends on the zone in which they are situated.

The allowed noise impact is:

Yellow zone (Gul sone): Lden 45 dB(A)

Red zone (Rød sone): Lden 55 dB(A)


The relevant zone can be selected in the noise receptor.


Alternative methods

The Norwegian guideline allows for noise to be calculated using alternative methods such as Nord2000. The 2017/2018 revision of the guideline focuses on the Nord2000 calculation. In the final assessment of noise impact in Norway is is likely that Nord2000 is required. A summary of Norwegian Nord2000 requirements is given in the according NORD2000 manual page.


Curtailment optimization considerations

It is not possible to use the noise matrix with Lden calculations and hence it is not possible to use the Norwegian model in the curtailment optimizer.


Alle Module
Handbuch DECIBEL auf einer Seite ♦ Handbuch NORD2000 auf einer Seite
Diese Seite: Norwegische Vorschrift, 2012/2017 (Englisch)
DECIBEL DECIBEL-ÜberblickDECIBEL-BerechnungDECIBEL-Ergebnisse
NORD 2000 NORD2000-ÜberblickNORD2000-BerechnungNORD2000-ErgebnisseNORD2000-Referenzen
Datengrundlage Schall-ImmissionsorteWEA-SchalldatenauswahlBearbeiten von Schalldaten im WEA-KatalogSchallmatrix
Liste der Schallmodelle ISO 9613-2 AllgemeinISO 9613-2 Deutschland (Interimsverfahren)ISO 9613-2 DeutschlandISO 9613-2 FinnlandISO 9613-2 FrankreichISO 9613-2 PolenISO 9613-2 Vereinigtes KönigreichDänemark 2019 (Englisch) ♦ Dänemark 2019 Tieffrequent (Englisch) ♦ Finnland TieffrequentNiederlande 2011 (Englisch) ♦ Norwegen 2012 (Englisch) ♦ Schweden 2009 (Englisch) ♦ Veraltete Schallmodelle
Sonstiges SchallreflexionenInteraktive IsophonenMaximalpegel-KarteManuelle Tieffrequenz-BerechnungGenerisches OktavbandMeteorologische DämpfungTechnischer Anhang (Englisch)