Category:WindPRO 3.4 Service Pack 2: Difference between revisions
Jump to navigation
Jump to search
No edit summary |
No edit summary |
||
| (15 intermediate revisions by 3 users not shown) | |||
| Line 1: | Line 1: | ||
Below you will find a list of all issues fixed in Service Pack 2: | |||
This Service Pack contains corrections to bugs reported by users. Thanks to all for submitting feedback. | |||
===BASIS=== | ===BASIS=== | ||
*Fixed issue where noise data would be labeled as source "USER" instead of "EMD" | *Fixed issue where noise data would be labeled as source "USER" instead of "EMD" {{Templink34SP2|06_0330}} | ||
*Fixed issue where georeferencing a map could cause an exception | *Fixed issue where georeferencing a map could cause an exception {{Templink34SP2|01_2759}} | ||
*Fixed issue where roads would not connect | *Fixed issue where roads would not connect {{Templink34SP2|01_2760}} | ||
*Fixed annoyance where loading PowerMatrix files containing unsupported data would generate a lot of error messages | *Fixed annoyance where loading PowerMatrix files containing unsupported data would generate a lot of error messages {{Templink34SP2|01_2678}} | ||
===DECIBEL=== | ===DECIBEL=== | ||
*Fixed issue in the manual check of automatically calculated noise values, where octave values could be falsely stated as available and "Start calculation" would be greyed out | *Fixed error in reflection distance calculation where the reflected distance would be overcompensated. Calculations using reflections made between windPRO version 3.4.404 and 3.4.414 should be recalculated. | ||
*Fixed issue in the manual check of automatically calculated noise value with redundant input | *Fixed issue in the manual check of automatically calculated noise values, where octave values could be falsely stated as available and "Start calculation" would be greyed out {{Templink34SP2|06_0329}} | ||
*Fixed issue in the | *Fixed issue in the manual check of automatically calculated noise value with redundant input {{Templink34SP2|06_0328}} | ||
===LOAD RESPONSE=== | |||
*Fixed issue where using an ed. 3 response model in ed.4 calculation would force the normalization loads to be locked to "using response model" (as for the generic) {{Templink34SP2|62_0010}} | |||
===METEO=== | ===METEO=== | ||
*Fixed issue where out-of-range data could be enabled from the "Data" | "Time series" tab | *Fixed issue where out-of-range data could be enabled from the "Data" | "Time series" tab {{Templink34SP2|25_0680}} | ||
*Fixed issue where a flag would not be displayed and it was not possible to jump to the next flag | *Fixed issue where a flag would not be displayed and it was not possible to jump to the next flag {{Templink34SP2|25_0675}} | ||
*Fixed issue where the rose view plot would hide signals when then number of sectors was increased | *Fixed issue where the rose view plot would hide signals when then number of sectors was increased {{Templink34SP2|25_0671}} | ||
===METEO ANALYZER=== | ===METEO ANALYZER=== | ||
*Improved time it takes to swap the axes of two large datasets in XY graph | *Improved time it takes to swap the axes of two large datasets in XY graph {{Templink34SP2|26_0148}} | ||
*Fixed annoyance in Weibull graph where line colors would be slightly different to the legend | *Fixed annoyance in Weibull graph where line colors would be slightly different to the legend {{Templink34SP2|26_0146}} | ||
*Fixed issue in Wiebull graph where the list of sectors would sometimes be limited to "All" when selecing heights with a different number of sectors. | *Fixed issue in Wiebull graph where the list of sectors would sometimes be limited to "All" when selecing heights with a different number of sectors. {{Templink34SP2|26_0145}} | ||
===ONLINE DATA=== | ===ONLINE DATA=== | ||
*Cancelling a climate data download no longer gives an error message | *Cancelling a climate data download no longer gives an error message {{Templink34SP2|22_0205}} | ||
===PARK=== | ===PARK=== | ||
* | *Fixed an error in the Time-varying N.O Jensen wake model. In our test-projects the relative differences in AEP going from 3.4 to 3.4 SP2 is typically ± 0.05%, but may be up to -0.52%. This is ONLY in org. N.O Jensen (PARK1) model and only by time varying calculations made in windPRO version 3.4 and 3.4 SP1. {{Templink34SP2|04_0699}} | ||
*Fixed issue where it was possible to select both "WakeBlaster request" and "WakeBlaster calculation" simultaneously | *Fixed issue where it was possible to select both "WakeBlaster request" and "WakeBlaster calculation" simultaneously {{Templink34SP2|04_0690}} | ||
*Improved message when scaler | *Improved message when scaler height is below displacement height {{Templink34SP2|04_0687}} | ||
===PERFORMANCE CHECK=== | ===PERFORMANCE CHECK=== | ||
*Fixed issue where setting the filter for "minimum number of WTGs operating simultaneous " would hide error codes in time series graph | *Fixed issue where setting the filter for "minimum number of WTGs operating simultaneous " would hide error codes in time series graph {{Templink34SP2|33_0602}} | ||
* | *Main statistics for error codes simplified, by removing mean and standard deviation to improve loading speeds {{Templink34SP2|33_0601}} | ||
*Fixed error where running an external PARK calculation from within Performance Check could cause loss of data | *Fixed error where running an external PARK calculation from within Performance Check could cause loss of data {{Templink34SP2|33_0600}} | ||
===PHOTOMONTAGE=== | ===PHOTOMONTAGE=== | ||
*Fixed error where Solar PV panels would be cut off if the Camera object was close to a very large Solar PV area | *Fixed error where Solar PV panels would be cut off if the Camera object was close to a very large Solar PV area {{Templink34SP2|58_0167}} | ||
===SHADOW=== | ===SHADOW=== | ||
*Added hidden | *Added hidden possibility to display extra decimals in shadow results. Contact support@emd.dk for more information {{Templink34SP2|07_0200}} | ||
===SITE COMPLIANCE=== | ===SITE COMPLIANCE=== | ||
* | *Fixed issue with Seismic data in Site Compliance. In certain projects the location of the Seismic map would be wrong {{Templink34SP2|29_0373}} | ||
*Fixed issue where | *Fixed issue where deleting the last remaining Shear value and adding a new one would throw an exception {{Templink34SP2|29_0367}} | ||
*Fixed annoyance where turbulence graph would not be fully painted (although visible) | *Fixed annoyance where turbulence graph would not be fully painted (although visible) {{Templink34SP2|29_0366}} | ||
*Fixed issue where removing calculations for air density, wind shear, flow inclination and effective turbulence could cause an exception | *Fixed issue where removing calculations for air density, wind shear, flow inclination and effective turbulence could cause an exception {{Templink34SP2|29_0364}} | ||
===Technical issue=== | ===Technical issue=== | ||
*Fixed issue where cancelling a IEC 61400-12-1 Angle & Terran check calculation would later create an empty report in the calculation list | *Fixed issue where cancelling a IEC 61400-12-1 Angle & Terran check calculation would later create an empty report in the calculation list {{Templink34SP2|21_0184}} | ||
=== | ===WAsP CFD=== | ||
* | *Fixed issue where "Site Data Object - Purpose: CFD" would not display the map of the calculation area, when using geographical coordinate systems. {{Templink34SP2|35_0069}} | ||
Latest revision as of 07:15, 15 January 2021
Below you will find a list of all issues fixed in Service Pack 2:
This Service Pack contains corrections to bugs reported by users. Thanks to all for submitting feedback.
BASIS
- Fixed issue where noise data would be labeled as source "USER" instead of "EMD"
- Fixed issue where georeferencing a map could cause an exception
- Fixed issue where roads would not connect
- Fixed annoyance where loading PowerMatrix files containing unsupported data would generate a lot of error messages
DECIBEL
- Fixed error in reflection distance calculation where the reflected distance would be overcompensated. Calculations using reflections made between windPRO version 3.4.404 and 3.4.414 should be recalculated.
- Fixed issue in the manual check of automatically calculated noise values, where octave values could be falsely stated as available and "Start calculation" would be greyed out
- Fixed issue in the manual check of automatically calculated noise value with redundant input
LOAD RESPONSE
- Fixed issue where using an ed. 3 response model in ed.4 calculation would force the normalization loads to be locked to "using response model" (as for the generic)
METEO
- Fixed issue where out-of-range data could be enabled from the "Data" | "Time series" tab
- Fixed issue where a flag would not be displayed and it was not possible to jump to the next flag
- Fixed issue where the rose view plot would hide signals when then number of sectors was increased
METEO ANALYZER
- Improved time it takes to swap the axes of two large datasets in XY graph
- Fixed annoyance in Weibull graph where line colors would be slightly different to the legend
- Fixed issue in Wiebull graph where the list of sectors would sometimes be limited to "All" when selecing heights with a different number of sectors.
ONLINE DATA
- Cancelling a climate data download no longer gives an error message
PARK
- Fixed an error in the Time-varying N.O Jensen wake model. In our test-projects the relative differences in AEP going from 3.4 to 3.4 SP2 is typically ± 0.05%, but may be up to -0.52%. This is ONLY in org. N.O Jensen (PARK1) model and only by time varying calculations made in windPRO version 3.4 and 3.4 SP1.
- Fixed issue where it was possible to select both "WakeBlaster request" and "WakeBlaster calculation" simultaneously
- Improved message when scaler height is below displacement height
PERFORMANCE CHECK
- Fixed issue where setting the filter for "minimum number of WTGs operating simultaneous " would hide error codes in time series graph
- Main statistics for error codes simplified, by removing mean and standard deviation to improve loading speeds
- Fixed error where running an external PARK calculation from within Performance Check could cause loss of data
PHOTOMONTAGE
- Fixed error where Solar PV panels would be cut off if the Camera object was close to a very large Solar PV area
SHADOW
- Added hidden possibility to display extra decimals in shadow results. Contact support@emd.dk for more information
SITE COMPLIANCE
- Fixed issue with Seismic data in Site Compliance. In certain projects the location of the Seismic map would be wrong
- Fixed issue where deleting the last remaining Shear value and adding a new one would throw an exception
- Fixed annoyance where turbulence graph would not be fully painted (although visible)
- Fixed issue where removing calculations for air density, wind shear, flow inclination and effective turbulence could cause an exception
Technical issue
- Fixed issue where cancelling a IEC 61400-12-1 Angle & Terran check calculation would later create an empty report in the calculation list
WAsP CFD
- Fixed issue where "Site Data Object - Purpose: CFD" would not display the map of the calculation area, when using geographical coordinate systems.
This category currently contains no pages or media.