Category:WindPRO 4.0 Service Pack 2

March 2024, build 4.0.540

Below you will find a list of all issues fixed in Service Pack 2

This Service Pack contains corrections to bugs and comments reported by users. Thanks to all for submitting feedback.

See list of previous releases here: windPRO releases

The items below are ordered alphabetically by module, then by importance.

BASIS

Fixed issue where importing WRF layers from windPROSPECTING would not work Go to TD in Story Manager
Copy/paste of power curve data in turbine catalogue will no longer include formatting Go to TD in Story Manager

DECIBEL

Fixed report issue for Finish Low Frequency calculation which could display too many frequencies. Recalculation required Go to TD in Story Manager
Fixed issue with conversion of noise data from 10m to HH for turbines with binned curtailments Go to TD in Story Manager
Fixed issue where a WTG with PowerMatrix could not be used in when using the setting "Wind speed at 95% of rated power" Go to TD in Story Manager
Fixed display issue in object form for noise results using pseudo wind speeds Go to TD in Story Manager Go to TD in Story Manager
Fixed report issue for DECIBEL calculations combining "Highest noise value at receptor" with uncertainty Go to TD in Story Manager
Fixed issue with warning about missing noise data appearing repeatedly for interactive noise line calculations Go to TD in Story Manager
Fixed issue with the reset of the "Use default value from calculation" and "Use default uncertainty margin from model" in the NSA object. Pure tone penalty setup deactivated in NSA, when calculating with German propagation model. Go to TD in Story Manager
Added a checkbox for deactivation of the additional result table in "DECIBEL, detailed results graphic" in the report properties Go to TD in Story Manager
Added message dialog if low frequency noise calculation has been configured to calculate "Distance to noise demand" and no turbines exceeded the threshold Go to TD in Story Manager
Increased the minimum height of the DECIBEL window Go to TD in Story Manager
Fixed window size of NSA setup for German translations Go to TD in Story Manager

LOSS & UNCERTAINTY

Fixed issue with "wrong format" warning when copy pasting curtailment setup. Go to TD in Story Manager

METEO

Fixed issues with calibration setup for Ammonit logger files Go to TD in Story Manager
Fixed issue with calculation of magnetic declination Go to TD in Story Manager
Fixed issue where the Meteo object would throw an irregular error message Go to TD in Story Manager
Fixed issue where importing only electricity prices would throw a false warning Go to TD in Story Manager
Fixed issue calculating concurrent time series in XY graph for time series with different time resolutions Go to TD in Story Manager
Fixed issue where scaled heights from a meteo object would not appear in selection window for scalers Go to TD in Story Manager

Fixed issue where entering a very large number (e.g. 999999) for "Days in window" would throw an exception Go to TD in Story Manager

Added ability to load data from the future Go to TD in Story Manager
Heights are now always displayed with 2 decimals Go to TD in Story Manager

MODEL

Slightly improved handling of Socket Error exception. Final solution has not been found.

NORD2000

Fixed issue converting noise from 10m height to hub height Go to TD in Story Manager
Fixed issue in main result report which could occur if "Always accepted" sound level exceeded ambient noise Go to TD in Story Manager
Fixed issue with reports for calculations which include ambient noise Go to TD in Story Manager

Go to TD in Story Manager

ONLINE DATA

Fixed issue where EMD-WRF On-demand would not allow spaces in name. This is now allowed Go to TD in Story Manager

PARK

Fixed issue with incorrect GROSS AEP in the report of time based PARK calculation, when more curtailments per time stamp was active. Go to TD in Story Manager
Fixed issue where entering the same value in "From" and "To" in the Displacement Height Calculator would produce 0-values Go to TD in Story Manager
Fixed issue where running a timevarying PARK calculation on a virtual machine with 2 cores would thrown an error message Go to TD in Story Manager
Fixed issue in IEC power curve correction where rated power would not be detected for certain power curves with high-wind ramp-down Go to TD in Story Manager
Added ability to see user label when selecting WTGs to include in report/ result to file Go to TD in Story Manager

PERFORMANCE CHECK

Fixed error with exception during the conversion of status logs in 10-min time series. Go to TD in Story Manager
Fixed issue where the source information of wind energy index would disappear after export Go to TD in Story Manager
Fixed issue with wind speed substitution if Performance Check was closed efter calculating correlations Go to TD in Story Manager
Post Construction and Model Validation concepts will now fill gaps if missing data is detected Go to TD in Story Manager
Added ability to create a meteo object for each turbine in the Performance Check profile with a "Select all"/"Deselect all" option Go to TD in Story Manager
Added warning if no power curves are detected in WTG-Objects Go to TD in Story Manager

RESOURCE

@ TGS Go to TD in Story Manager

SCRIPTING

Fixed issue where it was not possible to run a PARK calculation with turbines with curtailment Go to TD in Story Manager
Added properties in Sitedataobject Go to TD in Story Manager

SHADOW

Fixed issue with order of shadow receptors in report if one or more receptors had curtailments Go to TD in Story Manager
Added note to report for map with max hours/d in real case Go to TD in Story Manager
Added option to choose between real case reduction for receptors based on monthly or yearly aggregation Go to TD in Story Manager

SITE COMPLIANCE

Added ability to edit k and n parameters in Eurocode Go to TD in Story Manager

T-RIX tool

Fixed error in T-RIX report where WTGs with too low HH would appear in the "allowed" column Go to TD in Story Manager
Fixed error in T-RIX report where "vertical" was swapped with "horisontal" Go to TD in Story Manager
Fixed issue where the T-RIX report would always print UTM WGS84 instead of the project coordinate system Go to TD in Story Manager
Added option in T-TIX tool so it is possible to apply the User label as ID on the WTG and Reference tabs Go to TD in Story Manager
Improved error message in T-RIX tool when measurement heights were lacking Go to TD in Story Manager

TR10

Fixed issue with manually entered scaling factors Go to TD in Story Manager

This category currently contains no pages or media.